This website is currently under development and is being updated.
Logo

McNally Sayaji Engineering Limited

BAUXITE

Jaw Crushers

These are used as primary crushers in Bauxite Plants and also for spent anode butts.

Apron Feeders

These are extensively used to reclaim ROM/ Large Size ores from Dump Hoppers for primary crushing at mine end Ore Handling.

Apron Conveyors

These are used for conveying spent Anode Butts for recycling in Anode Paste Plants and are quite similar to Apron feeders in many respects, however these may be of curved alignment and long lengths (say up to 100 M).

Double Roll Crushers

These are used in crushing spent anodes in Anode Paste Plants of Aluminium Smelters.

Conveyor Components

MSEL product range includes all types of drive and non-drive pulleys, and idlers.

Motorised Trippers

Basically these are rail mounted conveyor discharging equipment to uniformly distribute the conveyed Ore over a large Bin or Ground Storage stockpile.

Grizzly Screens/ Feeders

These are used in primary crusher operation in Bauxite Mining as scalping screen downstream of the Primary Ore Crusher to separate undersized and oversized ore. Typical separation is at 80 mm. These are also used as Feeders to reclaim ore from Hoppers/Bins.

Rotary Disc Feeders

These are continuous volumetric device reclaiming dry small lumps, coarse, fine grained and powdery material e.g. coke breeze, ground bauxite, alumina etc. from surge bins and hoppers to feed subsequent equipment.

Circular Motion Screens

Also known as CM Screens, these are used to segregate various size fractions in ore streams. Sometimes used to reduce load on crushers by removing fraction which is already smaller than required size at other times these are used to recirculate oversize fractions from crushed product stream back to crushers. Possible application is in Mines before despatch to beneficiation plants as also in beneficiation plants. These Screens are available in 1, 2 and 3 decks to get 2, 3 and 4 size fractions respectively. Each size fraction may be requiring different post processing.

Linear Motion Screens

Linear Motion Screens are used for similar applications but in more demanding situations, e.g.-

  • Where the height is limited by surrounding facilities,
  • For the screening of small and short fractions
  • Where required throughput is high.

High Particle Acceleration Screens

These are ideally suited for heavy and very heavy screening applications for fine grain size materials (1 mm to 10 mm) with screening capacities up to 250 metric TPH. The base frame is agitated by means of eccentric shaft drive. The vibration is passed on to the dynamic frame via thrust rubbers.

Screening mats between the inner and outer frame are clamped and flexed by the two vibrating frames. The relative movement of both screening frames creates a “trampoline effect” in the screen mats to create-

  • High acceleration up to 50g in screen mats.
  • Loosening-up and de-agglomeration of the product.

Banana Screens

These are multi-slope vibrating screens, come in single/ two/ three deck configurations and are used in place of Circular Motion Screens when higher capacities (above 400 tph) are to be processed. The angle of deck decreases from feed end to discharge end.

Cone Crushers

MSEL has agency agreements with reputed manufacturers to sell these equipment, which are required as Secondary (-150/ 75 mm) and Tertiary Crushers (-30/ 10 mm) in Bauxite Crushing for Alumina production.

Reciprocating Feeders

These are built for high capacity reclamation from surge bins, bunker and hoppers. A wide range of sizes is available in MSEL offerings. Heavy Duty versions with larger drives and heavier pans can be selected for coarse ores and normal versions for fine ores

Bucket Elevators

These are used for vertical transport of powdery, small grained bulk materials e.g. raw meal, cement, sand, grits etc. They are used in filling tall bauxite and alumina silos.

Slurry Pumps

In Beneficiation plants usually the process involves transporting of Ore Slurry (suspension of Crushed/ Ground Ore in Water) between various stages. This is done by use of Slurry Pumps. MSEL has a vast range of Horizontal and Vertical Centrifugal Pumps catering to these requirements.

Rod Mills

Final crushed ore from tertiary crushers is ground to (-) 1 mm by rod mills. MSEL has a large range of rod mills to suit most ore characteristics and product requirements.

Ball Mills

These are used for size reduction to microns and form part of grinding circuit to get the final product for calcining or Alumina refining Process. These are also used in Coke Grinding for Carbon Paste preparation in Aluminium Smelters.

Thickeners

These are used to concentrate alumina Slurry (30-35% Solids) from refinery to about 60- 70 % Solids. Overflow product is mostly water and is recycled into circuit whereas the underflow is taken for evaporation circuit or to tailings as reject disposal.

Flotation

We can offer the Beneficiation/Up gradation solution for the Bauxite ore through flotation as part of total solution for this plant which will include Crushing, Grinding, Flotation, thickening, dewatering (Filtration), slurry pumping and system integration and plant design.